Angle Finder . . . . . . . . . . . . . . . . . . . . . . . . . (p/n 0644-097) Ball Hone . . . . . . . . . . . (p/n 0644-290, 291, 292, 293, 294) Coolant Cap (Non-Pressurized) . . . . . . . . . . (p/n 0644-156) Fan Spanner Wrench (Suzuki) . . . . . . . . . . . (p/n 0644-340) Flywheel Spanner Wrench . . . . . . . . . . . . . . (p/n 0144-007) Duck-Foot T-Handle Wrench (8 mm) . . . . . . (p/n 0644-332) EFI Throttle Cable Jam Nut/ Oil-Injection Pump Jam Nut Wrench . . . . (p/n 0644-242) Engine Stand . . . . . . . . . . . . . . . . . . . . . . . . (p/n 0644-079) Exhaust Spring Pliers . . . . . . . . . . . . . . (p/n 0644-391,397) Crankshaft Protector Cap . . . . . . . . . . . . . . . (p/n 0644-234) Flywheel Puller. . . . . . . . . . . . . . . . . . . . . . . (p/n 0744-040) Flywheel Puller. . . . . . . . . . . . . . . . . . . . . . . (p/n 0644-480) Flywheel Puller Insert . . . . . . . . . . . . . . . . . . (p/n 0644-179) Crankshaft Bearing Remover . . . . . . . . . . . . (p/n 0144-302) Idle Speed Screw Jam Nut Wrench . . . . . . . (p/n 0644-311) Linkage Wrench (8 mm). . . . . . . . . . . . . . . . (p/n 0644-333) Oil Filter Wrench(Adjustable). . . . . . . . . . . . (p/n 0644-389) Oil Injection Usage Tool . . . . . . . . . . . . . . . . (p/n 0644-007) Oil Seal Installation Tool . . . . . . . . . . . . . . . . (p/n 0644-219) Pinion Shimming Tool (650/700 cc Engines) . . . . . . . . . . . . . . . . (p/n 0644-055) Blind-Hole Bearing Puller . . . . . . . . . . . . . . . (p/n 0644-500) Piston Pin Puller . . . . . . . . . . . . . . . . . . . . . . (p/n 0644-328) Rigid Hone Stone Set (2.7-4.1 in.) . . . . . . . . (p/n 0644-043) Ring Compressor. . . . . . . . . . . . . . . . . . . . . (p/n 0644-378) Spring Tool . . . . .. . . . . . . . . . . . . . . . . . . . . (p/n 0644-072) Starter Assembly Tool . . . . . . . . . . . . . . . . . (p/n 0644-052) Stud Runner (6, 8, & 10 mm) . . . . . (p/n 0644-018,019,020) Surface Plate . . . . . . . . . . . . . . . . . . . . . . . . (p/n 0644-016) V Blocks . . . . . . .. . . . . . . . . . . . . . . . . . . . . (p/n 0644-022) Valve and Spring Retainer Tool . . . . . . . . . . (p/n 0644-448) Water Pump Bearing & Seal Kit . . . . . . . . . . (p/n 0644-502) Battery Charger . . . . . . . . . . . . . . . . . . . . . . (p/n 0436-634) Oil Pressure Test Kit . . . . . . . . . . . . . . . . . . . (p/n 0644-495) Compression Tester Kit . . . . . . . . . . . . . . . . (p/n 0444-213) Fuel Pressure Test Kit. . . . . . . . . . . . . . . . . (p/n 0644-493) EFI Analyzer . . . . . . . . . . . . . . . . . . . . . . . . . (p/n 0644-342) EFI Analyzer Update Kit. . . . . . . . . . . . . . . . (p/n 0744-046) EFI Analyzer Test Harness . . . . . . . . . . . . . . (p/n 0644-181) Test Harness Kit. . . . . . . . . . . . . . . . . . . . . . (p/n 0644-506) EFI Analyzer Test Harness . . . . . . . . . . . . . . (p/n 0639-624) Engine Timing Gauge. . . . . . . . . . . . . . . . . . (p/n 0144-009) Ignition Test Plug . . . . . . . . . . . . . . . . . . . . . (p/n 0144-306) Multimeter (Fluke Model 73 w/Case) . . . . . . (p/n 0644-191) Peak Voltage Reading Adapter. . . . . . . . . . . (p/n 0644-307) MaxiClips . . . . . .. . . . . . . . . . . . . . . . . . . . . (p/n 0744-041) Tachometer. . . . .. . . . . . . . . . . . . . . . . . . . . (p/n 0644-275) Timing Light . . . .. . . . . . . . . . . . . . . . . . . . . (p/n 0644-296) Vacuum Test Pump. . . . . . . . . . . . . . . . . . . . (p/n 0644-131) Laptop Diagnostic Tool . . . . . . . . . . . . . . . . . (p/n 0744-048) Alcohol Test Kit. . . . . . . . . . . . . . . . . . . . . . . (p/n 0644-044) Carburetor Adjustment Screwdriver (90°). . . (p/n 0644-289) Synchronizer Repair Kit . . . . . . . . . . . . . . . . (p/n 0644-062) Carburetor Synchronizing Tool Adapter . . . . (p/n 0644-023) Chip Puller . . . . .. . . . . . . . . . . . . . . . . . . . . (p/n 0644-188) Fuel Pump Socket Wrench . . . . . . . . . . . . . . (p/n 0644-364) Gas Gauge Removal Tool . . . . . . . . . . . . . . (p/n 0644-357) Carburetor Tool Set (Mikuni). . . . . . . . . . . . . (p/n 0636-072) Throttle Position Sensor (TPS) Adjustment ToolKit . . . . . . . . . . . . . . . . . . (p/n 3639-891) Bearing Cap Seal Protector . . . . . . . . . . . . . (p/n 0644-268) Bearing Cap Seal Protector . . . . . . . . . (p/n 0644-403,404) Bearing Removal Tool. . . . . . . . . . . . . . . . . (p/n 0644-421) Bearing Removal andInstallation Tool . . . . . (p/n 0644-167) Brake Disc Socket Wrench (ACT Drive). . . . (p/n 0644-415) Brake Disc Socket Wrench (ACT Drive). . . . (p/n 0644-481) Gear Case DrainPlug . . . . . . . . . . . . . . . . . (p/n 0644-504) Carbide & Stud Specifications Gauge . . . . . (p/n 1639-632) Clutch Alignment Bar. . . . . . . . . . . . . . . . . . (p/n 0644-320) Clutch Alignment Bar . . . . . . . .(p/n 0644-246,428,427,496) Clutch Compressor . . . . . . . . . . . . . . . . . . . (p/n 0644-420) Clutch Compressor (Arctic Round-Shaft). . . (p/n 0644-245) Clutch Compressor (Comet) . . . . . . . . . . . . (p/n 0644-123) Drive Clutch Bolt Tool (1/2-in. Drive) . . . . . . (p/n 0644-281) Clutch Puller (Arctic) . . . . . . . . . . . . . . . . . . (p/n 0644-207) Clutch Puller (Comet). . . . . . . . . . . . . . . . . . (p/n 0644-096) Clutch Puller (Comet). . . . . . . . . . . . . . . . . . (p/n 0644-100) Clutch Puller (4-Roller). . . . . . . . . . . . . . . . . (p/n 0644-446) Drive Belt Deflection Tool . . . . . . . . . . . . . . . (p/n 0644-412) Drive Belt Deflection Tool . . . . . . . . . . . . . . . (p/n 0644-424) Drive Belt Gauge . . . . . . . . . . . . . . . . . . . . . (p/n 0644-443) Drive Belt Replacement Tool . . . . . . . . . . . . (p/n 0644-435) Drive Clutch Spanner Wrench . . . . . . . . . . . (p/n 0644-136) Driven Pulley Puller . . . . . . . . . . . . . . . . . . . (p/n 0744-023) Driven Pulley Puller - ACT . . . . . . . . . . .(p/n 0644-469,468) Driven Pulley Compressor Tool . . . . . . . . . . (p/n 0644-444) Driven Pulley Spring Adjustment Tool . . . . . (p/n 0644-413) Reverse Gear Adjustment Gauge . . . . . . . . (p/n 0644-244) Roller Pin RemovalTool . . . . . . . . . . . . . . . . (p/n 0644-276) Spider Removal Kit . . . . . . . . . . . . . . . . . . . (p/n 0644-449) Spider Removal Kit (4-Roller) . . . . . . . . . . . (p/n 0644-505) Track Clip Installation Tool . . . . . . . . . . . . . . (p/n 0644-194) Track Stud HoleDrill (7 mm) . . . . . . . . . . . . (p/n 1639-629) Ball Joint Fork . . . . . . . . . . . . . . . . . . . . . . . (p/n 0644-098) Idler Wheel Alignment Tool . . . . . . . . . . . . . (p/n 0644-228) Idler Wheel Puller Kit . . . . . . . . . . . . . . .(p/n 0644-122,400) Floating Piston Location Gauge . . . . . . . . . . (p/n 0644-350) Floating Piston Removal Tool. . . . . . . . . . . . (p/n 0644-348) Floating Piston Installation/Location Tool Kit .(p/n 0644-402) Gas Shock Retaining Blocks (Zero Pro) . . . (p/n 0644-486) Gas Shock Rod/BodyClamping Tool . . . . . . (p/n 0644-425) Inflation Needle . . . . . . . . . . . . . . . . . . . . . . (p/n 0744-020) Inflation Needle Replacement . . . . . . . . . . . (p/n 0644-162) Nitrogen Regulator. . . . . . . . . . . . . . . . . . . . (p/n 0644-151) Piston Location Tool. . . . . . . . . . . . . . . . . . . (p/n 0644-169) Shock Absorber Air Pump . . . . . . . . . . . . . . (p/n 2603-614) Rear Shock Adjuster. . . . . . . . . . . . . . . . . . (p/n 0644-015) Shock Spanner Wrench . . . . . . . . . . . . . . . . (p/n 0644-447) Shock Spanner Wrench . . . . . . . . . . . . . . . . (p/n 0644-398) Shock Spanner Wrench . . . . . . . . . . . . . . . . (p/n 0644-305) Shock Spring Removal Tool . . . . . . . . . . . . . (p/n 0644-057) Spanner Wrench - Fox Float Shock . . . . . . . (p/n 0644-453) Rear Axle Nut Socket. . . . . . . . . . . . . . . . . . (p/n 0644-399) Axle Nut Spanner Wrench. . . . . . . . . . . . . . (p/n 0644-454) Ski Alignment Tool. . . . . . . . . . . . . . . . . . . . (p/n 0644-457) Rear Suspension Spring Tool . . . . . . . . . . . (p/n 0144-311) Hex Bits (1/4 in. Hex Drive) . . . . . . . . . .(p/n 0644-317,316) Insert Holder (5/16 in.) . . . . . . . . . . . . . . . . . (p/n 0644-315) Jack Stand . . . . . . .. . . . . . . . . . . (p/n 0644-076/2639-799) Phillips-Head Bits (1/4 in. Hex Drive) . . . (p/n 0644-319,318) Quick-Disconnect Coupler . . . . . . . . . . . . . . (p/n 0644-308) Replacement Bolt (Side) . . . . . . . . . . . . . . . (p/n 0644-101) Replacement Rivnuts . . . . . . . .(p/n 0623-557,582/627,581) (p/n 0623-699,874,529/779) Rivnut Tool. . .. . . . . . . . . . . . . . . . . . . . . . . (p/n 0644-232) Rivnut Tool Insert Bit . . .. . . . .(p/n 0644-233,405,430,431) Side Guard Kit . . . . . . . . . . . . . . . . . . . . . . . (p/n 0639-611) T-Handle Wrench . . . . . .. . . . .(p/n 0644-257,024,025,026) T Wrench . . . .. . . . . . . . . . . . . . . . . . . . . . . (p/n 0644-021) Torx Bit Insert (5/16 in. Hex Drive) . . . . . . . . (p/n 0644-314) Torx Bits (1/4 in. Hex Drive) . . .(p/n 0644-312,393,215,313) Angle Finder

0644-097

Ball Hone

p/n: 0644-290 (60-64 mm) p/n: 0644-291 (65-70 mm) p/n: 0644-292 (72-74 mm) p/n: 0644-293 (76-83 mm) p/n: 0644-294 (83-88 mm) Usage: Deglaze Nicosil plated cylinders. All are 320 grit and are recommended for reconditioning all Arctic Cat snowmobile engine cylinders (1976-2000).

0644-291

Coolant Cap (Non-Pressurized)

Fan Spanner Wrench (Suzuki)

Flywheel Spanner Wrench Duck-Foot T-Handle Wrench (8 mm)

0644-332

EFI Throttle Cable Jam Nut/Oil-Injection Pump Jam Nut Wrench (10 mm)

0644-242

Engine Stand Exhaust Spring Pliers (0°)

Exhaust Spring Pliers (90°)

Crankshaft Protector Cap

p/n: 0644-234 Usage: Protect the crankshaft end during flywheel removal.

0644-079

Flywheel Puller

p/n: 0744-040 (Complete Set) p/n: 0643-086 (Body) p/n: 0643-087 (Bolt) p/n: 0423-482 (6 mm Cap Screw) p/n: 0423-483 (8 mm Cap Screw) Usage: Pull flywheel off crankshaft on all Arctic Cat 2- stroke models.

0744-040

Flywheel Puller

0644-480

Flywheel Puller Insert

Crankshaft Bearing Remover

p/n: 0144-302 Usage: Remove crankshaft bearings.

Idle Speed Screw Jam Nut Wrench Linkage Wrench (8 mm)

0644-333

Oil Filter Wrench (Adjustable)

0644-389

Oil Injection Usage Tool

0644-007

Oil Seal Installation Tool

p/n: 0644-219 Usage: Install the oil seal on the water pump driveshaft on the 440, 550, 580, 650, 700, 800, and 900 cc Arctic Cat engines.

Pinion Shimming Tool (650/700 cc Engines)

p/n: 0644-055 Usage: Determine size and number of pinion gear shims.

Blind-Hole Bearing Puller

p/n: 0644-500 Usage: Remove bearing from water pump on Jaguar Z1.

AE152D

Piston Pin Puller

p/n: 0644-328 (Complete Set) p/n: 0643-073 (Extractor Nut Only-Small) p/n: 0643-074 (Extractor Nut Only-Medium) p/n: 0643-075 (Extractor Nut Only-Large) p/n: 0643-072 (Threaded T-Handle) Usage: Remove piston pins.

0644-328

Rigid Hone Stone Set (2.7-4.1 in.)

0644-043

Ring Compressor Spring Tool

Starter Assembly Tool

Stud Runner

p/n: 0644-018 (6 mm) p/n: 0644-019 (8 mm) p/n: 0644-020 (10 mm) Usage: Install studs on cylinders and crankcase.

0644-378

Surface Plate

0644-016

V Blocks

0644-022

Valve and Spring Retainer Tool

p/n: 0644-448 Usage: Adjust intake valve and exhaust valve “lash clearance” (2003-2006 660 cc 4-stroke engines).

0644-448

Water Pump Bearing & Seal Kit

p/n: 0644-502 Usage: Remove/install crankcase water pump bearings and seals.

DIAGNOSTICS

Battery Charger

p/n: 0436-634 Usage: Charge sealed, maintenance-free batteries.

Oil Pressure Test Kit

p/n: 0644-495 (Complete Kit) p/n: 0644-371 (8 mm Adapter) p/n: 0644-372 (10 mm Adapter) p/n: 0644-373 (12 mm Adapter) Usage: Test oil pressure on all Arctic Cat 4-stroke engines.

8

Compression Tester Kit

engines.

0444-213

Fuel Pressure Test Kit

0644-493

EFI Analyzer

p/n: 0644-342 (Complete Kit) p/n: 0644-422 (Harness) p/n: 3005-101 (Harness) p/n: 0643-124 (EPROM) p/n: 1686-310 (Harness) Usage: Troubleshoot 1992-2007 2-stroke Arctic Cat EFI systems including models with an exhaust temperature

sensor (except 2007 800 cc/1000 cc).

EFI Analyzer Update Kit

p/n: 0744-046 (Complete Kit) p/n: 0643-124 (EPROM) p/n: 1686-295 (Harness) p/n: 1653-368 (Instructions) Usage: Troubleshoot 1992-2007 2-stroke Arctic Cat EFI

systems including models with an exhaust temperature sensor (except 2007 800 cc/1000 cc).

EFI Analyzer Test Harness Test Harness Kit

p/n: 0644-506 (Complete Kit) p/n: 0644-497 (A. Laptop Harness) p/n: 0644-498 (B. Chassis Control Harness) p/n: 0644-499 (C. Chassis Control Harness) Usage: To attain diagnostic information on 2007 EFI models.

p/n: 0644-497 (A) Usage: Adapt laptop computer to 2007 800 cc/1000 cc engines to attain diagnostic information.

p/n: 0644-498 (B) Usage: Read chassis control unit codes on 2007 800 cc/ 1000 cc 2-stroke engines and 1100 cc 4-stroke engine.

p/n: 0644-499 (C) Usage: Read chassis control unit codes on 2007 500 cc/ 600 cc engines.

EFI Analyzer Test Harness

0639-624

Engine Timing Gauge

0144-009

Ignition Test Plug

Multimeter (Fluke Model 73 w/ Case)

p/n: 0644-191 Usage: Ditgital multimeter accurate to within ± 0.5%.

Peak Voltage Reading Adapter

p/n: 0644-307 Usage: With Fluke Model 73 Multimeter (p/n 0644-191), read peak voltage.

MaxiClips

0744-041

Tachometer

0644-275

Timing Light

0644-296

Vacuum Test Pump

Laptop Diagnostic Tool

FUEL SYSTEM

Alcohol Test Kit

p/n: 0644-044 Usage: Test gasoline for alcohol.

Carburetor Adjustment Screwdriver (90°)

0644-289

Synchronizer Repair Kit

0644-062

Carburetor Synchronizing Tool Adapter Chip Puller

Fuel Pump Socket Wrench

Gas Gauge Removal Tool

p/n: 0644-357 Usage: Remove gauge from the gas tank.

0644-023

Carburetor Tool Set (Mikuni)

0636-072

Throttle Position Sensor (TPS) Adjustment Tool Kit

p/n: 3639-891 (Complete Set) p/n: 0686-999 (Harness Only) p/n: 0644-359 (Torx-Head Screwdriver - #25

Only) p/n: 0644-344 (Torx-Head Screwdriver - #30

Only) p/n: 0644-345 (Pin Gauge Only) Usage: Precisely adjust the throttle position sensor on carbureted and EFI models.

3639-891

DRIVE SYSTEM/TRACK

Bearing Cap Seal Protector

p/n: 0644-268 Usage: Protect cap seal on rebuildable shock absorbers through 2002 models.

Bearing Cap Seal Protector

Bearing Removal Tool Bearing Removal and Installation Tool

0644-167

Brake Disc Socket Wrench (ACT Drive)

0644-415

Brake Disc Socket Wrench (ACT Drive) Gear Case Drain Plug

Carbide & Stud Specifications Gauge

Clutch Alignment Bar (1.365 in. Offset)

0644-481

Clutch Alignment Bar (1.562 in. Offset)

0644-246

Clutch Alignment Bar (1.485 in. Offset)

0644-428

Clutch Alignment Bar (1.655 in. Offset) Clutch Alignment Bar (1.507 in. Offset)

AE052A

Clutch Compressor

AE052A

Clutch Compressor (Arctic Round-Shaft)

0644-245

Clutch Compressor (Comet)

0644-123

Drive Clutch Bolt Tool (1/2-in. Drive) Clutch Puller (Arctic)

Clutch Puller (Comet)

Clutch Puller (Comet)

0644-281

Clutch Puller (4-Roller)

0644-446

Drive Belt Deflection Tool

0644-412

Drive Belt Deflection Tool Drive Belt Gauge

Drive Belt Replacement Tool

Drive Clutch Spanner Wrench

0644-424

Driven Pulley Puller

0744-023

Driven Pulley Puller - ACT

p/n: 0644-469 (Left-Hand Thread) p/n: 0644-468 (Right-Hand Thread) Usage: Remove ACT Driven Pulley from a corroded input shaft. Left-hand thread for models with a white sheave adjuster. Right-hand thread for models with a black sheave adjuster.

0644-469/468

Driven Pulley Compressor Tool

p/n: 0644-444 p/n: 0644-439 (A. Compressor Assembly Only) p/n: 0643-095 (B. Disc Only) Usage: Disassemble/assemble Arctic ACT and Team

Industries roller driven pulleys.

Driven Pulley Spring Adjustment Tool

Reverse Gear Adjustment Gauge Roller Pin Removal Tool

0644-276

Spider Removal Kit

p/n: 0644-449 (Complete Kit) p/n: 0744-037 (Handle) p/n: 0744-036 (Removal Tool) p/n: 0644-380 (Clutch Holder - 33 mm) p/n: 0744-035 (Clutch Holder - 30 mm) p/n: 0644-138 (Thin Wall Deep Socket - 1 7/16 in.) Usage: Disassemble/assemble/remove spider on Comet and Arctic drive clutches.

p/n: 0644-380 (33 mm) Usage: Hold clutch stationary sheave for 33 mm crank- shaft on 2001 and later 800/900 cc and 2003 and later 700 cc “Laydown” engines.

p/n: 0744-035 (30 mm) Usage: Aid in assembling/disassembling of 108 & 102C Comet and Arctic drive clutches.

0644-449

Spider Removal Kit (4-Roller)

p/n: 0644-505 (Complete Kit) p/n: 0644-473 (Clutch Holder - 35 mm) p/n: 0644-474 (Removal Tool) Usage: Disassemble/assemble/remove spider on 4-

roller drive clutch.

Track Clip Installation Tool

Track Stud Hole Drill (7 mm)

p/n: 1639-629 Usage: Drill 7 mm hole through rubber tracks for installing studs.

CHASSIS/SUSPENSION

Ball Joint Fork

0644-098

Idler Wheel Alignment Tool

0644-228

Idler Wheel Puller Kit

p/n: 0644-122 (Complete Kit - 6 in.) p/n: 0644-400 (Complete Kit - 8 in.) p/n: 0644-114 (A. Handle - 6 in.) p/n: 0644-401 (A. Handle - 8 in.) p/n: 0644-111 (B. Insertion Tool) p/n: 0644-120 (C. Pivot Plate) p/n: 0644-118 (D. Adapter Plate) p/n: 0623-310 (E. Cap Screw) p/n: 0644-119 (F. Puller Bolt) - 6 in. Kit p/n: 0644-432 (F. Puller Bolt) - 8 in. Kit Usage: Remove/install skid frame idler wheels.

Floating Piston Location Gauge

p/n: 0644-350 Usage: Precisely locate and measure floating piston depth without use of a calipers.

Floating Piston Removal Tool

0644-348

Floating Piston Installation/ Location Tool Kit

0644-402

Gas Shock Retaining Blocks (Zero Pro) Gas Shock Rod/Body Clamping Tool

Inflation Needle

Inflation Needle Replacement

0644-334

Nitrogen Regulator

0644-151

Piston Location Tool

0644-169

Shock Absorber Air Pump

2603-614

Rear Shock Adjuster

p/n: 0644-015 Usage: Rotate rear shock adjusting cam on external AFS models.

Shock Spanner Wrench

Shock Spanner Wrench

p/n: 0644-398 Usage: Adjust pre-load on front arm rebuildable shock absorber.

Shock Spanner Wrench

0644-305

Shock Spring Removal Tool

0644-057

Spanner Wrench - Fox Float Shock

0644-453

Rear Axle Nut Socket

Axle Nut Spanner Wrench

Ski Alignment Tool Rear Suspension Spring Tool

0144-311

MISCELLANY

Hex Bits (1/4 in. Hex Drive)

0644-316

Insert Holder (5/16 in.)

p/n: 0644-315 Usage: With Torx Bit Insert (p/n 0644-314), remove and install torx-head screws.

Jack Stand

Phillips-Head Bits (1/4 in. Hex Drive)

p/n: 0644-319 (#2) p/n: 0644-318 (#3) Usage: With Quick-Disconnect Coupler (p/n 0644-308),

remove and install Phillips-head screws.

Quick-Disconnect Coupler

0644-308

Replacement Bolt (Side)

0644-101

Replacement Rivnuts

p/n: 0623-557 (1/4 x 20) p/n: 0623-582/627 (1/4 x 20) p/n: 0623-581 (5/16 x 18) p/n: 0623-699 (3/8 x 16) p/n: 0623-874 (8-32) p/n: 0623-529/779 (10-32) Usage: With Rivnut Tool (p/n 0644-232), replace rivnuts.

Rivnut Tool

Rivnut Tool Insert Bit

p/n: 0644-233 (1/4 x 20) p/n: 0644-405 (10-32) p/n: 0644-430 (5/16 x 18) p/n: 0644-431 (3/8 x 16) Usage: With Rivnut Tool (p/n 0644-232) and Replace- ment Rivnuts, replace rivnuts.

Side Guard Kit

0623-557

T-Handle Wrench Torx Bit Insert (5/16 in. Hex Drive)

0644-314

0644-257

Torx Bits (1/4 in. Hex Drive)

p/n: 0644-312 (#25) T Wrench p/n: 0644-393 (#27) p/n: 0644-021 p/n: 0644-215 (#30)

Usage: Drive 3/8 in. square-drive sockets. p/n: 0644-313 (#40)

Usage: With Quick-Disconnect Coupler (p/n 0644-308), remove and install torx-head screws.

0644-021 0644-312

NOTES

NOTES

NOTES

Printed in U.S.A. ®™Trademarks of Arctic Cat Inc., Thief River Falls, MN 56701 p/n 2257-777